Few documents intimidate a first-time buyer like a diamond grading (per GIA's diamond grading standards) report. Dense tables, diagrams, and codes run across both sides of the page, and it is tempting to skim the headline grade and move on. But the report is where the real story of your diamond lives. Read it line by line, and you can judge value like a pro.

Start with the laboratory and the report number

At the top you will find the issuing laboratory — GIA, IGI, HRD, or another — and a unique report number. This is the first thing to record, because it is how you confirm the report is genuine and how you cross-check the stone's laser inscription on the girdle. Both GIA and IGI publish a free online check where you type the number and see the lab's own copy of the document.

Shape and measurements

The report states the stone's shape (round brilliant, princess, cushion, and so on) and its physical dimensions in millimetres, for example 6.32 x 6.28 x 3.91 mm. These numbers matter because they predict the actual size you will see on the hand. A 1.0-carat oval and a 1.0-carat round measure differently, and the mm range tells you how wide the stone will sit. If you are comparing shapes, our diamond shapes comparison explains the trade-offs.

Carat weight

Carat is the stone's weight, shown to two decimal places. A 1.02-carat diamond is technically just over one carat, which can change how it is priced and described. Remember that weight does not equal face-up size — depth and cut determine how much of the stone you actually see.

Colour grade

The colour grade runs D (colourless) through to Z (light yellow or brown). The report gives you a single letter. For a round brilliant in a white metal setting, most buyers target D through G for a near-colourless look; warmer I and J stones can look lovely in yellow gold and cost noticeably less. Our colour grading guide goes deeper into each band.

Clarity grade and the clarity characteristics

Clarity ranges from Flawless down to Included (I1–I3). The report also lists the specific inclusions — feathers, crystals, clouds, needles — and where they sit. Two diamonds with the same SI1 grade can feel very different depending on whether the inclusion is a tiny needle under the table or a black crystal near the edge. This is why an eye-clean stone often beats a marginally higher but more expensive grade.

Cut grade (round brilliants only)

GIA awards round brilliants a cut grade from Excellent down to Poor, based on proportions, light return, and finish. Fancy shapes do not receive a GIA cut grade; instead the report lists the measured proportions — table percentage, depth percentage, crown angle, pavilion angle, girdle thickness, and culet size. If those numbers look like a foreign language, start with our cut grade explainer. They describe how beautifully the stone handles light.

Finish: polish and symmetry

Polish and symmetry are each rated Excellent, Very Good, Good, Fair, or Poor. These describe how smoothly the facets meet and how evenly they are arranged. Excellent grades are the sweet spot; anything below Very Good can subtly affect sparkle.

Fluorescence

The report notes fluorescence — usually None, Faint, Medium, Strong, or Very Strong — and its colour, most often blue. Most fluorescence is harmless, but strong blue fluorescence can slightly mute a D–F stone in bright sunlight. See our fluorescence guide for the full picture.

The plots

The back of the report carries two diagrams: a clarity plot showing where the inclusions are located, and a proportions diagram. The plots are the map. They let a jeweller confirm that the stone in front of them matches the described inclusions, which is what makes the report tamper-resistant.

Symmetry, polish, and the footnotes

Two small fields are worth a second glance. Symmetry describes whether opposite facets line up evenly, and polish describes how smooth the facet surfaces are. Both are rated Excellent to Poor, and both quietly affect how crisp the sparkle looks. Below the main table you may also see comments on measurements, table and depth percentages, and a key to the plot symbols. These footnotes are technical, but a jeweller can read them aloud in thirty seconds if anything looks ambiguous.

If two reports look almost identical, the differences usually live in the proportions and the plot, not the headline grade. Train your eye on those two fields and the document stops being a wall of numbers.

What to take away

You do not need to memorise every code. On any report, focus on four fields — carat, colour, clarity, and cut — then glance at the plots and confirm the report number online. Read this way once or twice and the document stops looking like a labyrinth and starts looking like what it is: an objective description of the diamond you are considering.

Related Reading

Frequently Asked Questions

Is moissanite a good diamond alternative for retail buyers?

Yes for price-sensitive customers who want brilliance and hardness. Moissanite ranks 9.25 on the Mohs scale, holds up to daily wear and costs a fraction of a natural diamond of the same size, so it resells fast in bridal and fashion lines.

What is the minimum order for wholesale moissanite?

MOQ starts at 50 pieces per design for stock items. Custom cuts and private-label settings usually start at 100–300 pieces depending on the mold.

Do you provide certificates with moissanite stones?

Yes. Every parcel ships with GRA or IGI documentation listing carat weight, color grade and cut. We recommend passing the certificate to your end customer for trust.

How long does sample and bulk production take?

Samples ship in 3–5 days. Bulk runs take 15–20 days under 500 pieces, and 25–30 days for custom work.