A grader is comparing two 1.00ct round brilliants, both carrying a GIA Excellent cut grade. On paper they match. In the window light one looks crisp and tight, the other looks dull and heavy. The difference usually shows up in the lab report's proportions block, specifically the table percentage and the total depth percentage, which most retail buyers never read. Understanding these two numbers is the fastest way to tell an excellent cut that will sell from an excellent cut that will come back.
What table percentage actually measures
The table is the flat octagonal facet on the top of the stone, and its percentage is that facet's width divided by the diamond's average diameter. For a round brilliant, the sweet spot the trade reads as balanced runs from 53 to 58 percent. A table under 53 percent tends to push contrast and a darker, sharper look; over 62 percent the stone looks washed out, with broad white flashes that read as flat rather than bright. GIA documents the proportion system on its diamond cut grading page, and IGI uses the same proportion logic on its grading reference. The table is the single easiest number on a report to scan, so train buyers to read it before they read the price.
What total depth percentage measures
Total depth is the stone's full height, from the culet at the bottom to the top of the crown, divided by its diameter. This is where many supposedly Excellent stones fall apart. The accepted ideal band for a modern round sits between 59 and 62.6 percent. Above 64 percent the stone looks bottom-heavy: light leaks out through the pavilion instead of returning to the eye, and the face-up size on the hand looks smaller than its carat weight suggests. Below 56 percent the stone is too shallow, producing a fish-eye effect where the girdle reflection looks like a hollow ring in the center. Depth is not a visual charm a buyer can guess at; it is a measurement printed on every report.
How the two numbers work together
A table of 60 percent paired with a depth of 63 percent can still grade Excellent on proportions while looking heavier than a 55 percent table at 60 percent depth. The trade calls the first type a spread stone that loses face-up brightness. When you stock a bridal carousel, cross-reference table against depth rather than relying on the single letter grade. A 55 to 57 percent table combined with a 59 to 61.8 percent depth is the range that photographs well under studio light and holds up under store lighting. For the wider proportion story, read what cut grades actually matter and what makes a stone sparkle.
The retail trap with these two numbers
The trap is selling a 64 percent-depth stone as a value Excellent because the grade on the paper says so. Once mounted in a solitaire, that stone reads smaller and duller than a shallower, cheaper stone beside it. The reverse trap is rejecting a perfectly lively 58 percent table because a salesperson repeats that anything above 57 is too big. Stocking rule: flag any round over 63.5 percent depth or under 57 percent table for a side-by-side photo before listing it. Pair the numbers check with ideal versus very good cut and carat size versus face-up mm.
How crown and pavilion angles tie into table and depth
Table and depth do not float on their own. The crown angle, usually 34 to 35 degrees for an ideal round, controls how much white light returns. The pavilion angle, around 40.75 degrees, controls whether light exits through the table rather than leaking out the bottom. A stone with a 60 percent table and a 63 percent depth often pairs those numbers with a steeper crown or a deeper pavilion that reads heavy in person. When you pull a report, read the four numbers together: table, depth, crown angle, pavilion angle. A 55 percent table with a 34 degree crown and a 40.8 degree pavilion is the combination that photographs and sells. A 62 percent table with a 38 degree crown and a 41.5 degree pavilion will look dull even if the grade letter says Excellent. GIA lists the full proportion set on its proportion diagram, so train staff to scan the diagram, not just the grade.
What is a good table percentage for a round diamond?
Between 53 and 58 percent for a balanced, lively look. Around 55 to 57 percent is the range most bridal buyers perceive as bright without looking washed out.
What depth percentage makes a diamond look small?
Total depth above roughly 63 to 64 percent makes the stone look bottom-heavy and smaller face-up for its carat weight, because light leaks out the pavilion.
Do fancy shapes use the same table and depth ranges?
No. Cushions, ovals, and emerald cuts use different ideal proportion bands. The 53 to 58 table and 59 to 62.6 depth figures apply to round brilliants.
Is an Excellent cut always 60 percent depth?
No. Excellent is a grade that allows a range of proportions. Two Excellent stones can sit at 59 and 63.5 percent depth and look visibly different once mounted.
If you are a jeweler building a bridal carousel, our wholesale team can pull side-by-side proportion sheets on matched rounds before a parcel ships. Request a proportion comparison sheet.
Frequently Asked Questions
Is moissanite a good diamond alternative for retail buyers?
Yes for price-sensitive customers who want brilliance and hardness. Moissanite ranks 9.25 on the Mohs scale, holds up to daily wear and costs a fraction of a natural diamond of the same size, so it resells fast in bridal and fashion lines.
What is the minimum order for wholesale moissanite?
MOQ starts at 50 pieces per design for stock items. Custom cuts and private-label settings usually start at 100–300 pieces depending on the mold.
Do you provide certificates with moissanite stones?
Yes. Every parcel ships with GRA or IGI documentation listing carat weight, color grade and cut. We recommend passing the certificate to your end customer for trust.
How long does sample and bulk production take?
Samples ship in 3–5 days. Bulk runs take 15–20 days under 500 pieces, and 25–30 days for custom work.