When people talk about diamond sparkle, they usually mean the overall cut. But if you want to understand why two diamonds of the same carat, colour and clarity look so different, the numbers worth learning first are the table percentage and the crown angle. Both sit on the grading report, and both change how light behaves inside the stone.
What is the table of a diamond?
The table is the flat, four-sided (often appearing octagonal) facet that forms the top of the diamond. It is the single largest facet and the one your eye lands on first. Table percentage is simply the width of that table divided by the average diameter of the stone, expressed as a percentage. A diamond with a 57% table means the top facet spans 57% of the stone's width.
That ratio matters because it controls how much light enters directly through the top of the diamond versus through the angled crown facets around it. Too large a table and the crown becomes shallow, reducing the contrast between bright and dark areas that makes a round brilliant look alive. Too small a table and the stone can look dark or glassy from above, with a bloated centre that lacks the crisp pattern shoppers look for.
What is the crown angle?
The crown is the section of the diamond between the table and the widest point (the girdle). The crown angle is the slope of the bezel facets measured from the girdle plane. For a modern round brilliant, most ideal-cut charts place the target crown angle at about 34 to 35 degrees.
Crown angle and table percentage are trade-offs. When a cutter opens the table wider, the crown angle tends to become shallower to keep proportions balanced. That is why a report might show a 62% table paired with a 31.5-degree crown, and still score a Good rather than Excellent cut. The combination, not the isolated number, drives the result. A slightly shallower crown can be compensated by deeper pavilion angles, but only within limits.
Target numbers for a round brilliant
If you are comparing round brilliants, these are the commonly cited comfort zones used by independent cut graders:
- Table percentage: roughly 54% to 60% for an ideal to excellent stone.
- Crown angle: about 34 to 35 degrees.
- Pavilion angle: around 40.5 to 41 degrees (too deep and the stone leaks light through the bottom).
These ranges describe the round brilliant only. Fancy shapes such as ovals, pears and emeralds follow different proportion logic, and a strict table-percentage rule applied to them will mislead you. An emerald cut, for example, is graded more on its step-facet clarity and windowing than on a round-brilliant-style table. If you want the broader picture first, start with our guide to diamond cut grades.
Reading the numbers on a real report
On a GIA-style report the proportions are printed as a list: total depth, table, girdle, culet, crown angle and pavilion angle. You do not need a calculator to use them. If the table sits near 57% and the crown near 34.5 degrees, the stone is in the sweet spot. If the table reads 65% or the crown drops below 31 degrees, expect a softer, less contrasty stone unless the overall cut grade says otherwise. Symmetry and polish grades are printed separately; those tell you how precisely the facets were aligned, which our symmetry and polish grades guide explains.
Why cut grade beats chasing one number
A common mistake is filtering a search to "table under 57%" and ignoring everything else. Table and crown are two of roughly a dozen proportions that interact. Depth percentage, girdle thickness, star facet length, lower-half facet length, symmetry and polish all nudge the result up or down.
This is exactly why laboratories score a single overall cut grade rather than asking buyers to reverse-engineer optics from raw measurements. An Excellent or Ideal grade already means the combination of table, crown, pavilion and facet arrangement works. Compare that with reading the whole certificate, as covered in our guide to comparing two diamond certificates.
Does this apply to moissanite?
Moissanite is cut using the same round brilliant geometry, so table percentage and crown angle are still meaningful. The difference is that moissanite has a much higher refractive index and stronger dispersion, so the optics behave differently even at identical proportions. If you are weighing the two side by side, see diamond vs moissanite before you commit.
Practical takeaways
You do not need to become a gemologist to buy well. Read the table and crown numbers on the report, keep them inside the round-brilliant comfort zones, and let the overall cut grade be your tie-breaker. A well-cut 1.00 carat will out-sparkle a poorly cut 1.20 carat almost every time, which is the whole reason the cut matters more than the carat on the report. Treat the raw numbers as a sanity check, not as the final verdict.
Gemstone grading terminology used here follows the Gemological Institute of America’s gem encyclopedia.
Related Reading
- I1, I2, I3 Clarity: What Included Diamonds Actually Mean
- Diamond Table and Depth Percentages: What the Numbers Actually Mean
- VS1 vs VS2 Diamond Clarity: Which Grade to Buy
Frequently Asked Questions
Is moissanite a good diamond alternative for retail buyers?
Yes for price-sensitive customers who want brilliance and hardness. Moissanite ranks 9.25 on the Mohs scale, holds up to daily wear and costs a fraction of a natural diamond of the same size, so it resells fast in bridal and fashion lines.
What is the minimum order for wholesale moissanite?
MOQ starts at 50 pieces per design for stock items. Custom cuts and private-label settings usually start at 100–300 pieces depending on the mold.
Do you provide certificates with moissanite stones?
Yes. Every parcel ships with GRA or IGI documentation listing carat weight, color grade and cut. We recommend passing the certificate to your end customer for trust.
How long does sample and bulk production take?
Samples ship in 3–5 days. Bulk runs take 15–20 days under 500 pieces, and 25–30 days for custom work.