Almost nobody gets the size exactly right on the first try, and that is fine. Resizing is a routine job for any high-street jeweller. What is not routine is knowing in advance whether your ring is a ten-minute fix or a non-starter, and what a fair price looks like. This is the practical version.

What it costs in 2026

Ring typeUp or down 1 sizeUp or down 2 sizesTime
Plain 9ct/18ct band£25–£40£40–£602–5 working days
Platinum plain band£55–£80£80–£1205–10 days
Half-eternity / side-stone band£60–£100Often not advised1–2 weeks
Full-eternity / tension setUsually cannot be resized — ring must be remade—

When you should resize, and when to wait

Fingers change through life — weight shifts, pregnancy, hot weather, menopause. Resize only when the size feels stable for at least three months. If the ring is slightly loose, try a sizing bead (a tiny solder ball inside the band) before a full resize; it costs under £20 and is reversible. If the ring is too tight, do not wear it until it becomes uncomfortable enough to turn red; that is how rings get stuck and require cutting off, which costs more and risks the setting.

The technical bit, in plain English

Resizing down means cutting a small section out of the band and soldering the two ends back together. Resizing up generally stretches the band or adds a small piece of matching metal. Either way, the jeweller has to re-finish and re-polish the area. On a rhodium-plated white gold ring, the resized patch will look slightly brighter than the rest until the whole ring is re-dipped — most good shops include that in the price. Always ask.

Which rings cannot be resized

  • Full-eternity bands: stones run the whole circumference, so cutting the band breaks the setting.
  • Tension-set rings: the stone is held under engineered pressure; altering the band destroys the setting.
  • Ceramic, titanium or carbon-fibre bands: these are almost impossible to solder or stretch.
  • Vintage rings with enamel or engraved patterns: the heat of soldering will damage them.

How to choose the jeweller

The downsizing trap

Sizing a ring down by more than two sizes is a different job entirely. The band has to be cut and a section removed, which concentrates the solder point on one spot and can distort the roundness of the ring. If you need to go down three sizes or more, ask the jeweller whether a remake in the correct size would actually be cheaper and stronger. For a plain band, the answer is often yes; for a ring with stones, the answer is almost always to size by no more than one size in either direction and leave it at that.

Cheaper fixes before a full resize

If the ring spins around the finger or slips off when hands are cold, a full resize is not always the right first move. A sizing bead, a spring insert or a plastic ring guard can fix the fit for £10–£30, is fully reversible, and does not put the band through heat. Try one of these first if you are unsure of the new size — especially if weight, pregnancy or seasonal swelling might change the finger again in a few months.

When in the life of the ring to resize

Most resizes happen in the first month after the proposal, when the surprise measurement turns out to be half a size off. The second common window is after weight change, pregnancy or the menopause, when the finger genuinely changes for good. What you should not do is chase the daily wobble between a morning and an evening finger. If the ring fits comfortably at 3pm on a normal day, that is the size — the rest is just swelling. Resizing to fit a puffy evening finger will mean a loose ring three months later.

What the hallmark says about the repair

When a band is cut and soldered, the repaired area should be re-assayed if the repair materially alters the ring — in practice, most small resizes fall under the de minimis rule and do not need a new hallmark. A reputable jeweller will tell you whether your resize crosses that line. If you ever resell the ring, a clear, untouched hallmark is what a buyer looks for first, so keep the original box and any paperwork with the repair receipt inside it.

Ask three things before you hand the ring over: whether they do the work in-house or send it out (in-house is usually faster and cheaper), whether the price includes re-finishing and rhodium, and what their guarantee is if a stone loosens afterwards. Get a written quote and a receipt with the ring's hallmarks noted on it. A reputable shop will not flinch at any of this. For the broader upkeep calendar — cleaning, claw checks and insurance — see our jewellery care guide.

The Wikipedia article on rhodium explains why rhodium plating is applied to white gold and silver jewellery.

Related Reading

Frequently Asked Questions

What ring sizes can you supply in bulk?

US sizes 5–12 including half sizes. Send a size breakdown with your order and we cast to that curve; comfort-fit inner bands reduce resize requests.

Can I order a mixed size run instead of one size?

Yes. Mixed runs are standard for wholesale: specify quantity per size and we pack and label by size at no extra labor cost.

What is the MOQ for custom ring designs?

50 pieces per design for existing molds; 100–300 pieces when a new mold or CAD model is required.

How should I price rings for retail margin?

Most partners use a 3–4x markup on FOB cost for sterling and 2.5–3x for moissanite solos, which keeps landed cost under 30% of retail.