It is unsettling the first time you notice a fine scratch across a gold ring. The good news is that light scratches on gold are expected, not a sign of poor quality. The better news is that most of them can be reduced or removed. The nuance is how often you should do it, and which marks are better left alone.

Why gold scratches so easily

Pure gold (24k) is soft, which is why rings are alloyed with other metals. Even 18k gold is far softer than platinum and much softer than a hardened steel surface. Brushing past a door handle, resting your hand on a table, or sliding the ring into a pocket can leave micro-abrasions over months. The karat matters: 9k gold is harder and scratches less than 18k, which scratches less than 22k. Our 9ct vs 18ct wedding ring metal guide explains that trade-off in depth.

What polishing actually does

When a jeweller polishes a ring, they are not filling the scratch. They are abrading the surrounding surface down to the level of the scratch, so the whole band looks even again. Each polish removes a thin layer of metal. Done occasionally, this is harmless. Done every few months for years, it slowly thins the band and can soften the edges of engraved details or pavé settings.

The rule of thumb is to polish only when the scratches bother you, not on a schedule. A once-every-few-years refinish is reasonable; a yearly polish is not. If you bring the ring in for a service anyway, ask whether a light polish is needed rather than assuming it comes free.

Scratches on platinum vs gold

Platinum behaves differently. When platinum is scratched, the metal is displaced rather than worn away, which is why platinum rings develop a soft patina instead of thinning. Gold actually loses metal from a deep scratch, which is why over-polishing a gold band matters more than over-polishing a platinum one. If you are choosing between the two metals partly on wear, our platinum vs white gold comparison covers the long-term difference.

White gold and rhodium

White gold changes the picture. Most white gold rings are coated in a thin rhodium plating that gives them their bright white look. Scratches often show as the plating wears thin, and a re-plating hides them cleanly without polishing the underlying gold. That is why white gold owners are told to re-plate every year or two; see our ring repair and rhodium plating guide for the process and typical cost.

Scratches you should not polish out

Some marks are better left. A deep gouge that reaches a prong or a stone's girdle needs repair work, not polishing, because aggressive polishing around a setting can loosen stones. A matte or brushed finish cannot be "polished" without destroying the texture; it needs to be re-finished by the same method that created it. If in doubt, ask the jeweller to show you the scratch under magnification first.

DIY polishing mistakes to avoid

Around the home, avoid abrasive silver polishes, toothpaste, and scrubbing with a stiff brush, because each leaves its own fine swirl marks. Warm soapy water and a soft cloth is the safe default. Our jewellery care and cleaning at home guide lists the safe products. If a scratch is catching on fabric, that is a sign the metal has been burred up, and a jeweller can burnish it smooth in seconds without removing a whole layer.

Slowing new scratches down

You cannot prevent scratches on gold, but you can slow them. Take the ring off before heavy manual work, gardening, or gym sessions; store it on its own rather than tossed in a drawer with harder jewellery; and clean it regularly so fine grit does not sit against the band. Our jewellery habits that damage rings lists the everyday culprits.

Dents, not just scratches

A dent is different from a scratch, and polishing will not fix it. A deep ding on the side of the band needs the metal to be coaxed back into shape with small hammering and planishing, then refinished. That is a bench job, not a quick buff. If you catch the ring on a hard edge and see a visible crease, book a repair rather than waiting for the next clean, because dents can hide stress cracks that grow over time.

Polishing around stones

Any polishing near a pavé or prong setting carries a small risk: the jeweller's wheel can catch a bead or round a prong. This is why a careful jeweller will mask the stones before polishing, and why you should not use an at-home tumbler or aggressive cloth on a set ring. If your band is set, hand the polishing to a professional and keep the interval between refinishes long.

When a scratch is just patina

Many couples choose, after a few years, to leave the scratches. A ring with fine wear marks reads as a ring that is lived in and loved. Polishing is always available if you want it, but you are under no obligation to make a decade-old band look like it left the shop yesterday.

The Wikipedia article on rhodium explains why rhodium plating is applied to white gold and silver jewellery.

Related Reading

Frequently Asked Questions

What ring sizes can you supply in bulk?

US sizes 5–12 including half sizes. Send a size breakdown with your order and we cast to that curve; comfort-fit inner bands reduce resize requests.

Can I order a mixed size run instead of one size?

Yes. Mixed runs are standard for wholesale: specify quantity per size and we pack and label by size at no extra labor cost.

What is the MOQ for custom ring designs?

50 pieces per design for existing molds; 100–300 pieces when a new mold or CAD model is required.

How should I price rings for retail margin?

Most partners use a 3–4x markup on FOB cost for sterling and 2.5–3x for moissanite solos, which keeps landed cost under 30% of retail.