The most common cause of a lost centre stone is not a hard knock. It is a prong that has worn thin over years of daily wear. Re-tipping is the quiet repair that catches this problem before the stone falls out. Most people have never heard of it until their jeweller suggests it, and once they do, they wonder why they did not ask sooner.

What Are Prongs, and How Do They Wear?

Prongs are the little claws that grip a gemstone. On a solitaire there are usually four or six. Every time you wash your hands, type, carry shopping or brush past a surface, the prongs touch something. Over years, the tips rub against everything like tiny erasers. The metal thins. A prong that started round and sturdy becomes a sharp, paper-thin wire. Until that point you cannot see the problem with the naked eye, which is why we recommend the at-home check in our guide to checking prongs at home.

What Is Prong Re-Tipping?

Re-tipping is a jeweller's repair in which a small ball of matching metal (gold, platinum or palladium) is fused onto the worn tip of a prong, then shaped and polished to match the rest of the setting. The prong is rebuilt without taking the stone out, in most cases. It is cheaper than rebuilding the whole setting and far cheaper than replacing a lost diamond or moissanite.

Signs You Need Re-Tipping

  • A prong feels sharp or thin when you run a fingernail over it.
  • The stone moves slightly when you tap it with a finger.
  • A prong looks visibly shorter than its neighbours.
  • You have caught your ring on clothing or hair recently.
  • It has been more than two years since a jeweller last checked the setting.

If your stone is already loose, stop wearing the ring and book the repair. Our article on what to do if you lose a stone explains the worst-case path you want to avoid.

The Process, Step by Step

A good jeweller starts by examining the setting under magnification. They clean the ring, check each prong, and decide which tips need rebuilding. The stone is usually left in place. A tiny amount of matching metal is welded to the worn tip using a soldering laser or torch, then filed, shaped and polished to a smooth dome. The ring is cleaned and inspected again. Most re-tipping jobs take between one and three days in the workshop.

How Much Does It Cost?

Per prong, re-tipping typically costs a modest fee, with a small workshop minimum. Doing all six prongs on a solitaire is still far cheaper than the diamond sitting on top of them. Platinum settings cost slightly more because platinum is harder to work with. Always ask for a quote that includes cleaning, inspection and a tightened head, and read our broader ring repair and rhodium plating guide to compare costs.

How Often Should You Re-Tip?

Most rings need a check every 12 to 18 months. Rings worn daily, especially in active hands, may need re-tipping every two to three years. Rings rarely worn can go longer. The honest answer depends on your lifestyle, which is why an annual jeweller check is the cheapest insurance you will ever buy.

How to Make Prongs Last Longer

Remove your ring before heavy cleaning, gardening, gym work and showering with abrasive soaps. Store it on its own, not jumbled with other rings that scratch the prongs. Do not spin the ring on your finger out of habit; that micro-motion grinds the prongs against surfaces. Our habits that damage rings guide lists the rest.

Re-Tipping vs a Full Head Rebuild

Re-tipping fixes individual worn tips. If the whole setting (the "head") is bent, cracked or badly misshapen, re-tipping is not enough; the jeweller will recommend a full head rebuild, which replaces the entire basket of prongs and seats. Head rebuilds cost more than re-tipping but are still cheaper than replacing the ring. Your jeweller will explain which you need after inspecting the setting under magnification.

What Happens If You Delay

Delaying a re-tip is the most common way centre stones are lost. A thin prong can snap on a door handle, a sleeve or a bedsheet, and once the stone is loose it only takes one knock to send it into a drain or a grass verge. The repair cost is tiny; the replacement cost is not. If your jeweller recommends re-tipping, do it that week.

Bottom Line

Prong re-tipping is a small, routine repair that prevents a big, heartbreaking loss. Have your ring checked once a year, re-tip when the jeweller flags it, and your centre stone will stay on your finger for decades instead of vanishing into a drain. A five-minute annual inspection costs nothing and catches wear before it becomes a five-figure replacement.

The Wikipedia article on rhodium explains why rhodium plating is applied to white gold and silver jewellery.

Related Reading

Frequently Asked Questions

What ring sizes can you supply in bulk?

US sizes 5–12 including half sizes. Send a size breakdown with your order and we cast to that curve; comfort-fit inner bands reduce resize requests.

Can I order a mixed size run instead of one size?

Yes. Mixed runs are standard for wholesale: specify quantity per size and we pack and label by size at no extra labor cost.

What is the MOQ for custom ring designs?

50 pieces per design for existing molds; 100–300 pieces when a new mold or CAD model is required.

How should I price rings for retail margin?

Most partners use a 3–4x markup on FOB cost for sterling and 2.5–3x for moissanite solos, which keeps landed cost under 30% of retail.