On a diamond grading report, two numbers often confuse buyers: the table percentage and the depth percentage. They look like small arithmetic, but together they describe how light travels through the stone. Get them right and the diamond glows; get them wrong and it looks heavy, dark or glassy. Here is what each number actually means.
What Is the Table Percentage?
The table is the large, flat eight-sided facet on the very top of the diamond. The table percentage is the width of that facet divided by the total width of the diamond, expressed as a percentage. For a round brilliant, an ideal table is usually between 54% and 60%. A table that is too large (over 65%) can make the stone look flat and lifeless, reducing the contrast between bright and dark areas that creates sparkle. A table that is too small (under 52%) can overdo the contrast and make the centre look busy.
What Is the Depth Percentage?
The depth percentage measures the stone's total height, from the table on top to the culet at the bottom, divided by its width. A deep diamond hides carat weight below the girdle where no one can see it. A shallow diamond lets light leak out the bottom. For a round brilliant, ideal total depth usually lands between 59% and 62.5%. Anything above about 65% starts to look "bottom-heavy" and dull. Anything below about 56% looks washed out, often with a dark "fish-eye" through the table.
Why These Numbers Matter More Than Carat Alone
Two diamonds of the same carat weight can measure very differently. A 1-carat diamond cut too deeply might measure 6.0 mm across, while an ideal-cut 1-carat measures about 6.5 mm. You paid for a carat; you see a smaller face-up stone. This is why the proportions on the report matter as much as the weight on the scale. Our guide to ideal cut proportions goes deeper into the crown and pavilion angles that sit behind these two percentages.
How to Read Them on a Report
On a GIA or IGI report, the proportions block lists measurements in millimetres, then table %, depth %, crown angle, pavilion angle, girdle thickness and culet size. You do not need to memorise every range. Focus on table % and total depth % for round brilliants; for fancy shapes such as ovals and pears, depth % matters less because of the bowtie effect and elongated geometry.
Rough Ranges to Target
- Round brilliant table %: 54%–60% for ideal, up to 62% still good.
- Round brilliant total depth %: 59%–62.5% for ideal, up to 63.5% acceptable.
- Crown angle: around 34°–35° works best.
- Pavilion angle: around 40.5°–41° returns light to the eye.
If these ranges line up with a Good or Very Good cut grade, you are in safe territory. If the report says Poor or Fair on cut, even a perfect D/FL stone will underperform.
What About Fancy Shapes?
Ovals, pears, cushions and emerald cuts do not follow the same round-brilliant ranges. Emerald cuts, for example, are valued for step-facet clarity and windowed light, not the fire of a round. If you are choosing a fancy shape, read our oval, pear and cushion comparison before obsessing over table %.
Why Online Buyers Get Caught Out
Photographs lie more easily than numbers. A shallow diamond can be lit from above to look bright in a product shot, but on a finger under everyday light it will look dull. The proportions block on the grading report is your defence against that. Before you buy online, pull up the report and check the depth %. If the depth is over 65% for a round brilliant, expect a dark, heavy-looking stone regardless of how the photo looks. Our online diamond buying guide walks through the same checklist.
Table % and Depth % Work Together
Do not judge either number in isolation. A slightly deep diamond with a well-cut crown can still sparkle; a perfectly shallow one with a huge table will look washed out. Treat the two percentages as a pair, and let the overall cut grade on the report be the tie-breaker. If the cut grade is Excellent or Ideal, the proportions are already in balance.
Putting It Together
Table % controls how the top of the diamond looks. Depth % controls whether light escapes through the bottom. Both are visible on the grading report before you buy, which is exactly why checking the report beats guessing from a photograph. Use the percentages as a filter, then look at the stone in person or on 360-degree video before you commit. A few minutes spent on the proportions block saves buyers thousands of pounds every year.
Gemstone grading terminology used here follows the Gemological Institute of America’s gem encyclopedia.
Related Reading
- I1, I2, I3 Clarity: What Included Diamonds Actually Mean
- Diamond Table and Depth Percentages: What the Numbers Actually Mean
- VS1 vs VS2 Diamond Clarity: Which Grade to Buy
Frequently Asked Questions
Is moissanite a good diamond alternative for retail buyers?
Yes for price-sensitive customers who want brilliance and hardness. Moissanite ranks 9.25 on the Mohs scale, holds up to daily wear and costs a fraction of a natural diamond of the same size, so it resells fast in bridal and fashion lines.
What is the minimum order for wholesale moissanite?
MOQ starts at 50 pieces per design for stock items. Custom cuts and private-label settings usually start at 100–300 pieces depending on the mold.
Do you provide certificates with moissanite stones?
Yes. Every parcel ships with GRA or IGI documentation listing carat weight, color grade and cut. We recommend passing the certificate to your end customer for trust.
How long does sample and bulk production take?
Samples ship in 3–5 days. Bulk runs take 15–20 days under 500 pieces, and 25–30 days for custom work.